Shopping

• Fits most racing shocks with 5/8" shaft
• Durable hardened rubber construction
• Easy installation
• Superior protection
• Material: Hardened Rubber
• ID: 5/8”
• OD: 2”
• Height: 2-1/2"
• Overall diameter at large end is 1.938"
• Overall diameter at small end is 1.696"

• Rochester 2G Circle Track 500 CFM 2-Barrel Carburetor
• The JET 2G is IMCA approved
• Has a .135 needle and seat assembly for adequate fuel supply
• Small diameter float for maximum float bowl volume
• Cluster is modified based on engine and vehicle specs to keep the fuel curve correct throughout the RPM range
• Idle, transition and accelerator pump circuits are modified for circle track applications
• Tapped to accept Holley jets for ease of tuning and finished with a 3/8" fuel inlet
• Venture size: 1-3/8"
• Bore size: 1-11/16"
#NOTE: Due to the California Air Resources Board (CARB) restrictions, we no longer ship carburetors to the state of California.

• Steel bellhousing works with both small block Chevy and small block Ford engine bolt patterns
• Adapts either engine to Muncie/Saginaw pattern transmissions including BERT, Brinn, Falcon, etc.
• Bottom opening for easy access
• Does NOT have provision for stock style clutch arm
• WISSOTA approved for Midwest Modifieds
• Non SFI rated
• NOT for street use
• Must be used with a 153 tooth (Chevy) or 157 tooth (Ford) or smaller flexplate/flywheel
• Made in the USA

• Kit includes spindle, bolt-on "short" steering arm, caliper bracket and necessary hardware
• Assembly is required
• Choose (L) Left or (R) Right side
• Works great with our 1979-Up GM Metric front brake rotors, bearings, calipers, etc.
• IMCA approved for IMCA Modifieds and Sport Mod divisions only
• Forged, heat-treated steel
• Improves front end geometry
• Replacement for Pinto spindle
• Three-piece design for quick, easy replacement

• Kit includes spindle, bolt-on steering arm, caliper bracket and necessary hardware.
• Assembly is required
• Choose (L) Left or (R) Right side
• Works great with our 1979-Up GM Metric Front Brake Rotors, bearings, calipers, etc.
• Forged, heat-treated steel
• Precision OEM geometry
• Direct replacement for factory spindle
• Approved for use in IMCA sanctioned events
• Three-piece design for quick, easy replacement
• Replacement parts available separately

• NOTE: Includes steering arm only
• Works great with 1979-Up GM Metric Mid-Size spindles
• Choose (L) Left or (R) Right side
• Spindle body and caliper bracket available separately
• Forged, heat-treated steel
• Precision OEM geometry
• Approved for use in IMCA sanctioned events

For use with fresh air equipped helmets. Keeps dust and dirt out, provides cooler air inside the helmet, and prevents shield from fogging. Includes remote mount fan and filter assembly with 4' hose. 12 volt.

• 9.75" overall height
• 7.00" overall width
• 12 volt
• 49.50" tube length
• Sold each

• Rochester 2-barrel carburetor adapter plate for crate engines
• For use with 500 CFM rebuilt Rochester carburetor
• Plate is 0.515" thick
• 2-barrel 4-bolt flange type
• Bolt Pattern: Intake: (Inside: 5.625" x 4.250", Outside: 5.625" x 5.125"), Carb: 2" x 3.688"

• Rochester 2-barrel carburetor 2-hole base gasket
• Made from a durable heat-resistant nitrile rubber compound material
• Precision die cut for an excellent fit
• Works with Rochester 2GC "large base" (2" x 3-11/16" bolt pattern) two barrel carburetors
• Carb gasket is a 2-hole design that is 1/16" thick