Product Search

• Complete 600 Micro Sprint Rear Brake Carrier
• The aluminum single row bearing design saves weight over bulkier, more awkward designs
• Comes complete with snap ring and bolts, so you don't have to spend time searching for hardware to assemble your brake system
• 3.25" spread caliper mounts directly to carrier
• Anodized Black finish
• Weight: 1.6 lbs

At DaVinci Performance Carburetor ... We Make Horsepower! Our engineers aim to lead the industry in the research and development of fuel induction systems for products that exhibit maximum horsepower, engine efficiency, and environmental viability. You will find the very best workmanship in our custom carburetor modifications. Our promise to you is an out-of-the-box carburetor that will need minimal tuning.

• DaVinci Racing New Modified Holley® 4412 Carburetor
• Custom designed and modified for Circle Track Racing
• Aluminum with polished finish for great look
• Accelerator system modified to provide sharp dependable throttle response and prevent overfueling at higher RPM
• Includes Gaskets
• Fuel Type: Gasoline
• CFM: 500 CFM
• Choke Type: Manual
• Flange Type: 2-Barrel 4-Bolt
• Ready to run out of the box

#NOTE: Due to the California Air Resources Board (CARB) restrictions, we no longer ship carburetors to the state of California.

• Nitrophyl carburetor center float
• For 4150, 4160 & 4500
• Designed to control fuel slosh inside carburetor fuel bowl

Kits contain all components to install:
• One brake rotor / Hub assembly including hub seal
• Inner Bearing
• Outer Bearing
• Locknut Kit
• Dust Cap
• Bearing Kit for Metric Hub 1979-81

Aeromotive recommends annual inspection and service of filter elements. This includes replacing 10-micron fabric elements and cleaning or replacing 100-micron stainless steel elements. Severe duty applications or newly installed systems may require more frequent maintenance.

For Filter P/N’s: 12304, 12331, 12324, 12307, 12354

• QuickCar Switch Panel comes with 1 ignition switch, 1 starter button, and 1 accessory switch installed in a black plate
• Double pole toggle switches come with black protective boots
• Panel dimensions are 4-5/8" wide and 4-3/8" tall
• Panel comes assembled and pre-wired with mounting holes already punched out to make installation simple
• Switches come with colored indicator lights to signal if the switch is turned on or off
• All wires are professionally crimped, soldered, and heat shrunk for superior quality
• 50-822 is a direct fit to QuickCar's 50-200 (ignition box) or 50-201 (HEI) wiring harnesses
• Harness and installation hardware not included

• Performance RPM Series 110 Gph Fuel Pump
• Designed for Edelbrock Carburetors Performer RPM applications
• High performance Street Fuel Pump
• Features high quality 3-stage polished finish
• Valve design improves flow quantity and quality
• Supports engines up to 600 hp
• High-volume, 3/8" NPT inlet & outlet surpasses capacity of conventional models
• Produces 6 psi and does not require a regulator
• For gasoline only
• Clockable lower housing can be rotated for best Inlet/Outlet alignment

• 1-Gallon Drag Fuel Cell, 7" x 7" x 8"
• Crosslink Polyethylene
• -08 AN Rollover Vent
• -08 AN Fuel Return
• Two -08 AN Fuel Pickups at Bottom Rear of Tank
• 12 Bolt Heavy Duty Aircraft - Style Flush Mount Lid Assembly

• Sprint Car Header
• Welded to clear 4 inches from head to inside of header
• Forward Design for additional muffler clearance
• 32" primary, 18 gauge tubing, long collector
• Forward Design for additional muffler clearance
• Bolts & gaskets included