Item # 12610Aeromotive recommends annual inspection and service of filter elements. This includes replacing 10-micron fabric elements and cleaning or replacing 100-micron stainless steel elements. Severe duty applications or newly installed systems may require more frequent maintenance.
For Filter P/N’s: 12310, 12311, 12360
Item # 66-508• Kit contains 2 of each color bushings
• 2 extra soft, blue
• 2 soft, yellow
• 2 medium, red
• 2 hard, black
Item # 6201• Higher output with 530 primary volts and 135mJ of spark energy
• Efficient components use less current to produce more power
• Same bolt pattern as the original 6AL with a lower profile housing
• Built-in LED for system checks
• All wires exit the same side through a locked, sealed connector
• Compatible for 4, 6 or 8-cylinder engines
• Secondary Voltage: 45,000 Volts
• Spark Series Duration: 20 degree Crankshaft Rotation
• RPM Range: 15,000 RPM with 14.4 Volts
• Voltage Required: 12-15 Volts, 7 Volt Start
• Current Draw: .7 Amp per 1,000 RPM
• Weight and Size 1.7 lbs., 8"L x 4"W x 1.825"H
Item # 71396PennGrade motor oil, formerly known as Brad Penn, has been endorsed for decades by racers, engine builders, and manufacturers. These high-performance oils deliver excellent shock load and temperature protection to engine parts for both racers and every day drivers.
• SAE 30W High-Performance Motor Oil
• Film strength/protection under demanding torque
• Anti-foaming, stability and high temperature protection
• Detergent/dispersant additives for engine cleanliness
• Oxidation and foam inhibitors to protect against thermal degradation, air entrainment
The result is reduced internal friction, strong anti-wear, and increased horsepower.
Item # REM-PLMETRIC• PEM GM Metric Bearing and Race Kit with Seal for One Wheel
• REM Finished
• Polished bearings and races for GM Metric front hub (LM12649, LM12610, LM67048, LM67010)
• Two bearings and two races for one wheel - micro polished
• With standard hub seal
• Used in IMCA/USRA stock car classes and many other stock car racing series
• Common bearings for GM metric mid size cars 1978-1988
Item # 550-052• Rochester 2-barrel carburetor 2-hole base gasket
• Made from a durable heat-resistant nitrile rubber compound material
• Precision die cut for an excellent fit
• Works with Rochester 2GC "large base" (2" x 3-11/16" bolt pattern) two barrel carburetors
• Carb gasket is a 2-hole design that is 1/16" thick
Item # 1222F• 22 Gallon WEDGE STYLE
• 24.5 L x 24.5 W x 15 H
• Mounts with the width side to side with the fittings toward front
• Fuel Return: #8
• Rollover Vent: #8
• Fuel Pickup: #10
• 16 Bolt Oval 2.5 inch Lid Fill Plate Assembly with Flapper
• Aluminum Billet Cap
• Fuel Pickup in Right Rear Side
• Spot Welded Steel Container
• Fully Powder Coated Finish
• Cross Linked Polyethylene Bladder
• Can Also Connect Remote Hose to Fill Plate
Item # SC-CH-0007• Sprint Car Torque Tube Hoop
• 4130 chromoly
• 13" length
Item # 26-2• Heli-Coil installation tool kit
• For Fuel Bowl Screws
• Tap
• Need 15/64” drill bit
Item # 8202• Improved output coil for electronic ignitions, Blaster Ignition or MSD 5, 6, & 7 Series (ballast resistor required for points)
• Alkyd tower with high dielectric properties is less prone to carbon tracking
• 100:1 turns ratio & lower primary resistance produce high voltage output
• Metal canister filled with premium grade oil for cooling
• CARB E.O. Approved