Zamp Racing Helmets

• Top Air Intake Vent plus Chin Bar Vents which allows option to Run
• Forced Air Accessory Option
• Smaller Shell
• Composite Kevlar Mix Lightweight Shell
• Plush Fire Retardant Interior
• Z-21 Series 2.5mm Clear Shield
• Rear Spoiler Included for Aerodynamics
• Removable/Washable Comfort Cheek Pads and Crown Liner
• Snell CMR2016

• Top Air Intake Vent plus Chin Bar Vents which allows option to Run
• Forced Air Accessory Option
• Smaller Shell
• Composite Kevlar Mix Lightweight Shell
• Plush Fire Retardant Interior
• Z-21 Series 2.5mm Clear Shield
• Rear Spoiler Included for Aerodynamics
• Removable/Washable Comfort Cheek Pads and Crown Liner
• Snell CMR2016

• Exclusively from Zamp... Photochromatic Shields
• Go from bright to dark racing conditions without having to change shields!
• The new Z-20 Photochromatic Shield smoothly transitions from clear to dark smoke (or vice versa) depending on the brightness of the track, without having to change the shield!
• One shield works for Night or Day

• The Zamp Z-24 Anti-fog visors are available in a wide array of options, including: Clear, Light Smoke, Dark Smoke, Amber, Prism (Green, Blue, Gold, Red, Purple), Irridium, Silver Mirror, Polarized Smoke and Photochromatic.
• The Zamp Z-24 photochromatic Shield go from bright to dark racing conditions without having to change shields
• One shield works for Night or Day!
• The new Z-24 Photochromatic visor comes in a single option at this point, allowing the smooth transition from clear to dark (or vice versa) depending on the brightness of the race track without having to change the shield!
• Zamp-Racing recommends that you periodically change shields for better vision and safety.

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.

• Carbon Mix Shell - Super lightweight construction for reduced driver fatigue
• DDAIR-SYSTEM - New 360° Dual-Density Air Channeling for superior forced air cooling
• Advanced Aerodynamics - Aero Lips built into shell, plus accessory options: adjustable rear spoiler and chin bar front spoiler
• TRI-Tech Air System - Adjustable inlets on top of helmet and both sides of chin bar for Natural Air, Forced Air, or Air Plugs - the most versatile air system on the market
• 28 Series Plush Interior - Removable, washable, fire-retardant ultra-soft cheek pads and crown liner
• Z-20 Series Clear Anti-Fog Shield - Equipped with tensioning tear-off posts, compatible with 12.125" banana-style tear offs or Z Optics P208Z Tear Offs
• Hydration Ready - Built-in center chin bar hydration port with removable plug
• Audio Ready - Includes Ear Cups and Ear Pads for reduced noise and easy communication integration
• M6 Inserts - Head & Neck Restraint compatible
• Snell SA2025 Approved

• Carbon Mix Shell - Super lightweight construction for reduced driver fatigue
• DDAIR-SYSTEM - New 360° Dual-Density Air Channeling for superior forced air cooling
• Advanced Aerodynamics - Aero Lips built into shell, plus accessory options: adjustable rear spoiler and chin bar front spoiler
• TRI-Tech Air System - Adjustable inlets on top of helmet and both sides of chin bar for Natural Air, Forced Air, or Air Plugs - the most versatile air system on the market
• 28 Series Plush Interior - Removable, washable, fire-retardant ultra-soft cheek pads and crown liner
• Z-20 Series Clear Anti-Fog Shield - Equipped with tensioning tear-off posts, compatible with 12.125" banana-style tear offs or Z Optics P208Z Tear Offs
• Hydration Ready - Built-in center chin bar hydration port with removable plug
• Audio Ready - Includes Ear Cups and Ear Pads for reduced noise and easy communication integration
• M6 Inserts - Head & Neck Restraint compatible
• Snell SA2025 Approved