Helmet Shields

• Replacement shields for Roux SA2015 and SA2020 helmets.
• These helmet shields fit all Roux helmet styles.
• Shields available in Clear, Amber/Yellow, Dark Smoke, Light Smoke or Blue Irridium.

• SE07 3mm DSAF Shield
• Injection-molded optically correct polycarbonate face shield with a Double Screen Anti-Fog insert for superior fog control
• Uses the SV (SE07, SE077) pivot kit
• Compatible with tearoffs, and is available in a variety of colors
• Compatible with the HP7, RS7C LTWT, RS7SC LTWT, RS7 Carbon, RS7K Carbon, RS7, and RS7K

• SE03 3mm DSAF shield
• Injection-molded optically correct polycarbonate face shield with a Double Screen Anti-Fog insert for superior fog control
• uses the SV (SE03/SE05) pivot kit
• Compatible with tearoffs, and is available in a variety of colors
• Compatible with the GTX3 Carbon, GTX3, GP3 Carbon, and GP3

Simpson helmet shields are offered in clear as well as stylish and functional tints. When ordering a shield for your racing or motorcycle helmet, keep these considerations in mind:

• Clear shields are generally used for night racing or very low-light conditions
• Amber shields provide a minimal amount of tinting that's ideally suited to overcast weather
• Yellow shields are often used in dawn or dusk driving, as they tend to accentuate track features
• Tinted shields can help eliminate glare during daytime driving
• Some people find that mirrored shields block even more sunlight than tinted shields and Iridium shields provide the most protection from both sunlight and glare

• Exclusively from Zamp... Photochromatic Shields
• Go from bright to dark racing conditions without having to change shields!
• The new Z-20 Photochromatic Shield smoothly transitions from clear to dark smoke (or vice versa) depending on the brightness of the track, without having to change the shield!
• One shield works for Night or Day

• The Zamp Z-24 Anti-fog visors are available in a wide array of options, including: Clear, Light Smoke, Dark Smoke, Amber, Prism (Green, Blue, Gold, Red, Purple), Irridium, Silver Mirror, Polarized Smoke and Photochromatic.
• The Zamp Z-24 photochromatic Shield go from bright to dark racing conditions without having to change shields
• One shield works for Night or Day!
• The new Z-24 Photochromatic visor comes in a single option at this point, allowing the smooth transition from clear to dark (or vice versa) depending on the brightness of the race track without having to change the shield!
• Zamp-Racing recommends that you periodically change shields for better vision and safety.

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.