Item # 35500• Best chemical sealer you can buy to stop cooling system leaks
• Works equally well in aluminum or cast iron blocks
• Cooling system must be thoroughly clean before use
• Does not work with antifreeze
Item # 71206PennGrade motor oil, formerly known as Brad Penn, has been endorsed for decades by racers, engine builders, and manufacturers. These high-performance oils deliver excellent shock load and temperature protection to engine parts for both racers and every day drivers.
• 30W High-Performance Break-in Oil
• Formulated specifically to meet critical lubrication needs of new engines during break-in
• Allows proper seating of rings and component ‘run-in’
• Enhanced levels of “zinc” and superior oil film strength from Penn Grade™ base oils
• Offers complete anti-wear, anti-scuffing protection for even the most demanding of applications such as those presented by break-in of engines with ‘flat tappet’ cams
Item # 71396-12PennGrade motor oil, formerly known as Brad Penn, has been endorsed for decades by racers, engine builders, and manufacturers. These high-performance oils deliver excellent shock load and temperature protection to engine parts for both racers and every day drivers.
• SAE 30W High-Performance Motor Oil
• Film strength/protection under demanding torque
• Anti-foaming, stability and high temperature protection
• Detergent/dispersant additives for engine cleanliness
• Oxidation and foam inhibitors to protect against thermal degradation, air entrainment
• Case of 12 quarts
The result is reduced internal friction, strong anti-wear, and increased horsepower.
Item # 71156PennGrade motor oil, formerly known as Brad Penn, has been endorsed for decades by racers, engine builders, and manufacturers. These high-performance oils deliver excellent shock load and temperature protection to engine parts for both racers and every day drivers.
• SAE 50W High-Performance Motor Oil
• Film strength/protection under demanding torque
• Anti-foaming, stability and high temperature protection
• Detergent/dispersant additives for engine cleanliness
• Oxidation and foam inhibitors to protect against thermal degradation, air entrainment
The result is reduced internal friction, strong anti-wear, and increased horsepower.
Item # 71506Designed to meet the lubrication demands of traditional classic and muscle car engines as well as high-performance competition engines, Brad Penn Grade 1 Partial Synthetic SAE 10W-30 High Performance Oil offers the multi-viscosity advantages of faster oil flow and engine warm-up as well as excellent film strength and engine component anti-wear protection.
• Grade 1® Partial Synthetic SAE 10W-30 High Performance Oil
• Suitable for engines used both on the street and/or the track
• Multi-viscosity grade & synthetic components facilitate cold starting & quicker engine warm-up
• Ensures adequate engine protection during competition
Item # 71196Designed to meet the lubrication demands of traditional classic and muscle car engines as well as high-performance competition engines, Brad Penn Grade 1 Partial Synthetic High Performance Oil offers the multi-viscosity advantages of faster oil flow and engine warm-up as well as excellent film strength and engine component anti-wear protection.
• Semi-synthetic SAE 20W-50 High Performance Oil
• Offers engines cold temp benefits of SAE 20W and film strength
• Superior sealing abilities
• Bearing, crankshaft, piston ring and valvetrain component anti-wear protection
Item # 80022• Will not foul oxygen sensors
• Replaces almost any cut gasket
• Makes reliable "formed-in-place" gaskets that resist cracking, shrinking & migrating
• Coats pre-cut gaskets to increase reliability
• Temp range -65°F to 500°F intermittent
• Applications - valve covers, oil pans, timing covers, water pumps, thermostat housings, transmission pans
Item # 00106• Viscosity typical of SAE 15W-50
• Highest levels of zinc & phosphorus for flat-tappet engines
• Additives promote ring seal & maximum protection during break-in
• Good for full power pulls on dyno
• maximum compression & horsepower
• For methanol & high-octane race fuels
Item # 00006• Viscosity typical of 5W-20
• Designed to handle 500 miles of competition, over 9500 rpm & temps above 250°
• Anti-wear & friction reducing additives reduce friction & fight valve-train wear
• Use with methanol & high octane race fuels
Item # 00206• Viscosity typical of 0W-20
• Low viscosity synthetic oils for increased horsepower without decreased durability
• Anti-wear & friction reducing additives reduce friction & fight valve-train wear
• Use with methanol & high octane race fuels